Gilliner® 1366B and 1366E are high impact resistant grade liners constructed of woven E- and S-glass cloth with a polyester resin system to optimize strength, weight and cost. This product offers superior mechanical properties and higher strength-to-weight ratio compared to all E glass constructions. 1 mil. white polyvinyl fluoride film overlay on the face side is included for Gilliner® 1366E.
一般用途的飛機貨艙內襯。
| 厚度，英寸（毫米） | 0.011 (0.28) 0.050 (1.27) 0.020 (0.51) 0.060 (1.52) 0.030 (0.76) 0.070 (1.78) 0.040 (1.02) 0.090 (2.29) 0.045 (1.14) |
| 長度 | 紙張形式最大 168 英寸（4,267 毫米） 卷狀典型長度為 150 英尺（45,720 毫米） |
| 寬度，英寸（毫米） | 典型 48 (1,219)，最多 72 (1,829) |
| 顏色 | 自然色或白色 |
以下測試按照BMS 8-2規範要求進行。
| TGC 部件號 | 1366B011 | 1366B020 | 1366B030 | 1366B045 | 1366B070 | |
|---|---|---|---|---|---|---|
| 厚度，英寸（毫米） | 0.011 (0.28) | 0.020 (0.51) | 0.030 (0.76) | 0.045 (1.14) | 0.070 (1.78) | |
| 最大重量，psf（kg/m2) | 0.13 (0.63) | 0.21 (1.03) | 0.32 (1.56) | 0.50 (2.44) | 0.74 (3.61) | |
| 抗拉強度1, 西 (兆帕) | 經 | > 50 (340) > 50 (340) | > 50 (340) > 50 (340) |
|||
| 充滿 | ||||||
| 抗彎強度2, 西 (兆帕) | 經 | 不適用 | ≥ 30 (210) | |||
| 充滿 | ||||||
| 彎曲正切模量2, 微星 (GPa) | 經 | 不適用 | ≥ 2.5 (17) | |||
| 充滿 | ||||||
| 吸水率3, % 增加 | < 2.0 | < 2.0 | < 2.0 | < 2.0 | < 2.0 | |
| Bond Strength – Warp4, 磅力 (N) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | |
| 抗磨性5, g/1000 次循環 | < 0.17 | < 0.17 | < 0.17 | < 0.17 | < 0.17 | |
| 衝擊強度6, 英尺-磅 (牛米) | 13 (18) | 16 (22) | 20 (27) | 32 (43) | 47 (64) | |
| 邊緣承載強度7, 西 (兆帕) | 經 | ≥ 40 (270) ≥ 40 (270) |
||||
| 充滿 | ||||||
| 易燃 | 符合 FAR 25.853 和 855 附錄 F 第 I 和 III 部分 | |||||
所示表格反映了典型值，不應用作設計規範。
1拉伸強度根據 ASTM D638 進行測試和計算。
2彎曲強度和模量根據 ASTM D790 進行測試和計算。
3根據 ASTM D570 測試和計算吸水率。
4根據 ASTM D5868 使用改進的樣品製備和測試速度測試和計算粘合強度。
5耐磨性是根據 ASTM D3389 使用 CS-10 輪、500 克重量和對樣品製備進行微小修改進行測試的。
6衝擊強度是根據 ASTM D5420 使用改進的落鏢和試樣測試框架測試計算得出的。
7邊緣承載強度是根據 ASTM D953 使用改進的張力加載夾具計算的。
當遵循推薦的預防措施時，本產品可以安全使用和應用。使用本產品前，請閱讀並理解 安全數據表 (SDS)，其中提供有關健康、身體和環境危害、處理預防措施和急救建議的信息。僅供工業使用。遠離兒童。可以在以下位置找到更多信息： www.thegillcorp.com.如需銷售和訂購信息，請致電 1-626-443-6094。
All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.
