PAA-CORE® 5052 aluminum honeycomb is phosphoric acid anodized and coated with a proprietary primer. PAA-CORE® has unsurpassed corrosion resistance, (with minimal weight loss after 31 days in an acidified salt spray chamber). PAA-CORE® outperforms non-metallic core materials due to significantly higher strength-to-weight ratio and hot/wet strength.
| 标准 | 最大限度 | 宽容 | ||||
|---|---|---|---|---|---|---|
| 英寸 | 毫米 | 英寸 | 毫米 | 英寸 | 毫米 | |
| 丝带（大） | 48 | 1219 | 100 | 2540 | +2.0 / -0.0 | +50.8 / -0.0 |
| 横向 (W) | 96 | 2438 | 144 | 3658 | +4.0 / -0.0 | +101.6 / -0.0 |
| 厚度 (T) | 35 | 889 | ||||
| 高达 4 英寸（102 毫米）T | ±0.005 | ±0.127 | ||||
| 超过 4 英寸（102 毫米）T | ±0.062 | ±1.575 | ||||
| 密度 | 见机械特性表 | ±10% | ||||
| 像元大小 | 见机械特性表 | ±10% | ||||
基质： 5052铝
涂层： PAA底漆
When ordering, please specify PAA-CORE® 5052 using the following format:
Example: PAA – 5052 – 3.1 – 3/16 – N – E, where
| 产品 | 合金 | 密度 | 像元大小 | 穿孔或非穿孔 | 扩展或未扩展 |
|---|---|---|---|---|---|
| PAA | 5052 | 3.1 | 3/16 | A片 | E或U |
| Mechanical Characteristics (Typical Values – US units) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 稳定压缩 力量 | 压碎 力量 | 剪切 力量 | 剪切 模数 |
||||||
| 磅/英尺3 – inches – inches | 压力 | 压力 | 压力 | ksi | |||||
| 大号 | W | 大号 | W | ||||||
| 75° F | 350° F | 75° F | 75° F | 350° F | 75° F | 350° F | 75° F | ||
| 3.1 – 1/8 – .0007 | 305 | 200 | 145 | 215 | 145 | 132 | 90 | 32 | 16 |
| 4.5 – 1/8 – .0010 | 580 | 380 | 270 | 345 | 240 | 225 | 150 | 51 | 25 |
| 6.1 – 1/8 – .0015 | 1030 | 660 | 450 | 565 | 400 | 345 | 220 | 77 | 37 |
| 8.1 – 1/8 – .0020 | 1575 | 1075 | 760 | 810 | 575 | 540 | 310 | 112 | 50 |
| 10.0 – 1/8 – .0025 | 1875 | 1300 | 1070 | 1075 | 810 | 610 | 415 | 140 | 60 |
| 12.0 – 1/8 – .0030 | 2920 | 1550 | 1400 | 1955* | 1300* | 950* | 440 | 160 | 75 |
| 2.6 – 5/32 – .0007 | 245 | 150 | 105 | 170 | 110 | 102 | 80 | 24 | 12 |
| 3.8 – 5/32 – .0010 | 415 | 280 | 210 | 275 | 200 | 168 | 140 | 41 | 20 |
| 2.0 – 3/16 – .0007 | 180 | 100 | 70 | 122 | 80 | 71 | 65 | 17 | 9 |
| 3.1 – 3/16 – .0010 | 340 | 200 | 145 | 215 | 145 | 128 | 90 | 32 | 16 |
| 4.4 – 3/16 – .0015 | 555 | 375 | 270 | 335 | 235 | 220 | 145 | 50 | 24 |
| 5.7 – 3/16 – .0020 | 870 | 600 | 410 | 465 | 380 | 305 | 200 | 70 | 34 |
| 6.9 – 3/16 – .0025 | 1185 | 780 | 570 | 600 | 500 | 380 | 275 | 91 | 42 |
| 8.1 – 3/16 – .0030 | 1735 | 1075 | 760 | 735 | 575 | 490 | 310 | 112 | 50 |
| 2.3 – 1/4 – .0010 | 215 | 125 | 85 | 145 | 90 | 88 | 70 | 21 | 11 |
| 3.4 – 1/4 – .0015 | 375 | 235 | 160 | 235 | 160 | 145 | 100 | 35 | 18 |
| 4.3 – 1/4 – .0020 | 545 | 365 | 250 | 325 | 235 | 205 | 140 | 48 | 24 |
| 5.2 – 1/4 – .0025 | 770 | 500 | 330 | 415 | 330 | 270 | 160 | 62 | 31 |
| 6.0 – 1/4 – .0030 | 1110 | 650 | 430 | 535 | 390 | 350 | 210 | 75 | 36 |
| 7.9 – 1/4 – .0040 | 1505 | 1025 | 720 | 710 | 550 | 450 | 300 | 108 | 49 |
| 1.6 – 3/8 – .0010 | 98 | 70 | 50 | 88 | 60 | 51 | 35 | 13 | 6 |
| 2.3 – 3/8 – .0015 | 205 | 125 | 85 | 145 | 90 | 88 | 70 | 21 | 11 |
| 3.0 – 3/8 – .0020 | 315 | 190 | 135 | 205 | 140 | 128 | 85 | 30 | 15 |
| 3.7 – 3/8 – .0025 | 415 | 265 | 200 | 255 | 190 | 165 | 105 | 40 | 20 |
| 4.2 – 3/8 – .0030 | 565 | 340 | 240 | 315 | 230 | 205 | 130 | 47 | 23 |
| 5.4 – 3/8 – .0040 | 810 | 540 | 360 | 435 | 355 | 285 | 180 | 66 | 32 |
| 6.5 – 3/8 – .0050 | 1015 | 750 | 510 | 555 | 440 | 360 | 265 | 83 | 40 |
| 4.0 – 1/2 – .0040 | 400 | 320 | 220 | 290 | 220 | 170 | 120 | 44 | 22 |
有关最小值，请参阅 AMS-C-7438。 *梁剪切
| Mechanical Characteristics (Typical Values – SI/metric units) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 稳定压缩 力量 | 压碎 力量 | 剪切 力量 | 剪切 模数 |
||||||
| 磅/英尺3 – inches – inches | 兆帕 | 兆帕 | 兆帕 | 兆帕 | |||||
| 大号 | W | 大号 | W | ||||||
| 23° C | 177° C | 23° C | 23° C | 177° C | 23° C | 177° C | 23° C | ||
| 3.1 – 1/8 – .0007 | 2.10 | 1.38 | 1.00 | 1.48 | 1.00 | 0.91 | 0.62 | 221 | 110 |
| 4.5 – 1/8 – .0010 | 4.00 | 2.62 | 1.86 | 2.38 | 1.65 | 1.55 | 1.03 | 352 | 172 |
| 6.1 – 1/8 – .0015 | 7.10 | 4.55 | 3.10 | 3.90 | 2.76 | 2.38 | 1.52 | 531 | 255 |
| 8.1 – 1/8 – .0020 | 10.86 | 7.41 | 5.24 | 5.58 | 3.96 | 3.72 | 2.14 | 772 | 345 |
| 10.0 – 1/8 – .0025 | 12.93 | 8.96 | 7.38 | 7.41 | 5.58 | 4.21 | 2.86 | 965 | 414 |
| 12.0 – 1/8 – .0030 | 20.13 | 10.69 | 9.65 | 13.48* | 8.96* | 6.55* | 3.03* | 1103 | 517 |
| 2.6 – 5/32 – .0007 | 1.69 | 1.03 | 0.72 | 1.17 | 0.76 | 0.70 | 0.55 | 165 | 83 |
| 3.8 – 5/32 – .0010 | 2.86 | 1.93 | 1.45 | 1.90 | 1.38 | 1.16 | 0.97 | 283 | 138 |
| 2.0 – 3/16 – .0007 | 1.24 | 0.69 | 0.48 | 0.84 | 0.55 | 0.49 | 0.45 | 117 | 62 |
| 3.1 – 3/16 – .0010 | 2.34 | 1.38 | 1.00 | 1.48 | 1.00 | 0.88 | 0.62 | 221 | 110 |
| 4.4 – 3/16 – .0015 | 3.83 | 2.59 | 1.86 | 2.31 | 1.62 | 1.52 | 1.00 | 345 | 165 |
| 5.7 – 3/16 – .0020 | 6.00 | 4.14 | 2.83 | 3.21 | 2.62 | 2.10 | 1.38 | 483 | 234 |
| 6.9 – 3/16 – .0025 | 8.17 | 5.38 | 3.93 | 4.14 | 3.45 | 2.62 | 1.90 | 627 | 290 |
| 8.1 – 3/16 – .0030 | 11.96 | 7.41 | 5.24 | 5.07 | 3.96 | 3.38 | 2.14 | 772 | 345 |
| 2.3 – 1/4 – .0010 | 1.48 | 0.86 | 0.59 | 1.00 | 0.62 | 0.61 | 0.48 | 145 | 76 |
| 3.4 – 1/4 – .0015 | 2.59 | 1.62 | 1.10 | 1.62 | 1.10 | 1.00 | 0.69 | 241 | 124 |
| 4.3 – 1/4 – .0020 | 3.76 | 2.52 | 1.72 | 2.24 | 1.62 | 1.41 | 0.97 | 331 | 165 |
| 5.2 – 1/4 – .0025 | 5.31 | 3.45 | 2.28 | 2.86 | 2.28 | 1.86 | 1.10 | 427 | 214 |
| 6.0 – 1/4 – .0030 | 7.65 | 4.48 | 2.96 | 3.69 | 2.69 | 2.41 | 1.45 | 517 | 248 |
| 7.9 – 1/4 – .0040 | 10.38 | 7.07 | 4.96 | 4.90 | 3.79 | 3.10 | 2.07 | 745 | 338 |
| 1.6 – 3/8 – .0010 | 0.68 | 0.48 | 0.34 | 0.61 | 0.41 | 0.35 | 0.24 | 90 | 41 |
| 2.3 – 3/8 – .0015 | 1.41 | 0.86 | 0.59 | 1.00 | 0.62 | 0.61 | 0.48 | 145 | 76 |
| 3.0 – 3/8 – .0020 | 2.17 | 1.31 | 0.93 | 1.41 | 0.97 | 0.88 | 0.59 | 207 | 103 |
| 3.7 – 3/8 – .0025 | 2.86 | 1.83 | 1.38 | 1.76 | 1.31 | 1.14 | 0.72 | 276 | 138 |
| 4.2 – 3/8 – .0030 | 3.90 | 2.34 | 1.65 | 2.17 | 1.59 | 1.41 | 0.90 | 324 | 159 |
| 5.4 – 3/8 – .0040 | 5.58 | 3.72 | 2.48 | 3.00 | 2.45 | 1.97 | 1.24 | 455 | 221 |
| 6.5 – 3/8 – .0050 | 7.00 | 5.17 | 3.52 | 3.83 | 3.03 | 2.48 | 1.83 | 572 | 276 |
| 4.0 – 1/2 – .0040 | 2.76 | 2.21 | 1.52 | 2.00 | 1.52 | 1.17 | 0.83 | 303 | 152 |
有关最小值，请参阅 AMS-C-7438。 *梁剪切
当遵循推荐的预防措施时，本产品可以安全使用和应用。使用本产品前，请阅读并理解 安全数据表 (SDS)，其中提供有关健康、身体和环境危害、处理预防措施和急救建议的信息。仅供工业使用。离孩子远点。其他信息可在以下位置找到： www.thegillcorp.com.如需销售和订购信息，请致电 1-626-443-6094。
All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.
