Gilliner® 1366B and 1366E are high impact resistant grade liners constructed of woven E- and S-glass cloth with a polyester resin system to optimize strength, weight and cost. This product offers superior mechanical properties and higher strength-to-weight ratio compared to all E glass constructions. 1 mil. white polyvinyl fluoride film overlay on the face side is included for Gilliner® 1366E.
一般用途的飞机货舱内衬。
厚度,英寸(毫米) | 0.011 (0.28) 0.050 (1.27) 0.020 (0.51) 0.060 (1.52) 0.030 (0.76) 0.070 (1.78) 0.040 (1.02) 0.090 (2.29) 0.045 (1.14) |
长度 | 纸张形式最大 168 英寸(4,267 毫米) 卷状典型长度为 150 英尺(45,720 毫米) |
宽度,英寸(毫米) | 典型 48 (1,219),最多 72 (1,829) |
颜色 | 自然色或白色 |
以下测试是根据 BMS 8-2 规范要求运行的。
TGC 部件号 | 1366B011 | 1366B020 | 1366B030 | 1366B045 | 1366B070 | |
---|---|---|---|---|---|---|
厚度,英寸(毫米) | 0.011 (0.28) | 0.020 (0.51) | 0.030 (0.76) | 0.045 (1.14) | 0.070 (1.78) | |
最大重量,psf(kg/m2) | 0.13 (0.63) | 0.21 (1.03) | 0.32 (1.56) | 0.50 (2.44) | 0.74 (3.61) | |
抗拉强度1, 西 (兆帕) | 经 | > 50 (340) > 50 (340) | > 50 (340) > 50 (340) |
|||
充满 | ||||||
抗弯强度2, 西 (兆帕) | 经 | 不适用 | ≥ 30 (210) | |||
充满 | ||||||
弯曲正切模量2, 微星 (GPa) | 经 | 不适用 | ≥ 2.5 (17) | |||
充满 | ||||||
吸水率3, % 增加 | < 2.0 | < 2.0 | < 2.0 | < 2.0 | < 2.0 | |
Bond Strength – Warp4, 磅力 (N) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | ≥ 500 (2200) | |
抗磨性5, g/1000 次循环 | < 0.17 | < 0.17 | < 0.17 | < 0.17 | < 0.17 | |
冲击强度6, 英尺-磅 (牛米) | 13 (18) | 16 (22) | 20 (27) | 32 (43) | 47 (64) | |
边缘承载强度7, 西 (兆帕) | 经 | ≥ 40 (270) ≥ 40 (270) |
||||
充满 | ||||||
易燃 | 符合 FAR 25.853 和 855 附录 F 第 I 和 III 部分 |
所示表格反映了典型值,不应用作设计规范。
1拉伸强度根据 ASTM D638 进行测试和计算。
2弯曲强度和模量根据 ASTM D790 进行测试和计算。
3根据 ASTM D570 测试和计算吸水率。
4根据 ASTM D5868 使用改进的样品制备和测试速度测试和计算粘合强度。
5耐磨性根据 ASTM D3389 使用 CS-10 砂轮、500 克重物进行测试,并对样品制备进行了微小修改。
6冲击强度是根据 ASTM D5420 使用改进的落镖和试样测试框架测试计算得出的。
7边缘承载强度是根据 ASTM D953 使用改进的张力加载夹具计算的。
当遵循推荐的预防措施时,本产品可以安全使用和应用。使用本产品前,请阅读并理解 安全数据表 (SDS),其中提供有关健康、身体和环境危害、处理预防措施和急救建议的信息。仅供工业使用。离孩子远点。其他信息可在以下位置找到: www.thegillcorp.com.如需销售和订购信息,请致电 1-626-443-6094。
All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.