Gilliner® 1366B/1366E

Overview

Gilliner® 1366B and 1366E are high impact resistant grade liners constructed of woven E- and S-glass cloth with a polyester resin system to optimize strength, weight and cost. This product offers superior mechanical properties and higher strength-to-weight ratio compared to all E glass constructions. 1 mil. white polyvinyl fluoride film overlay on the face side is included for Gilliner® 1366E.

Applications

Aircraft cargo compartment liner for general purpose use.

Features

High impact strength
Abrasion resistant
Corrosion resistant
Fire resistant

Availability

Thickness, inch (mm)	0.011 (0.28) 0.050 (1.27) 0.020 (0.51) 0.060 (1.52) 0.030 (0.76) 0.070 (1.78) 0.040 (1.02) 0.090 (2.29) 0.045 (1.14)
Length	Maximum 168 inch (4,267 mm) in sheet form Typical 150 feet (45,720 mm ) in roll form
Width, inch (mm)	Typical 48 (1,219), Maximum 72 (1,829)
Color	Natural or White

Construction

N/A

Specifications

FAR Part 25, Appendix F Parts I and III (burn through)

Performance Properties, Typical

The following tests are run in accordance with BMS 8-2 specification requirements.

TGC Part Number		1366B011	1366B020	1366B030	1366B045	1366B070
Thickness, inch (mm)		0.011 (0.28)	0.020 (0.51)	0.030 (0.76)	0.045 (1.14)	0.070 (1.78)
Maximum Weight, psf (kg/m²)		0.13 (0.63)	0.21 (1.03)	0.32 (1.56)	0.50 (2.44)	0.74 (3.61)
Tensile Strength¹, ksi (MPa)	Warp	> 50 (340) > 50 (340)				> 50 (340) > 50 (340)
	Fill	> 50 (340) > 50 (340)
Flexural Strength², ksi (MPa)	Warp	N/A			≥ 30 (210)
Flexural Strength², ksi (MPa)	Fill	N/A			≥ 30 (210)
Flexural Tangent Modulus², Msi (GPa)	Warp	N/A			≥ 2.5 (17)
Flexural Tangent Modulus², Msi (GPa)	Fill	N/A			≥ 2.5 (17)
Water Absorption³, % Increase		< 2.0	< 2.0	< 2.0	< 2.0	< 2.0
Bond Strength – Warp⁴, lbf (N)		≥ 500 (2200)	≥ 500 (2200)	≥ 500 (2200)	≥ 500 (2200)	≥ 500 (2200)
Abrasion Resistance⁵, g/1000 cycles		< 0.17	< 0.17	< 0.17	< 0.17	< 0.17
Impact Strength⁶, ft-lb (N-m)		13 (18)	16 (22)	20 (27)	32 (43)	47 (64)
Edge Bearing Strength⁷, ksi (MPa)	Warp	≥ 40 (270) ≥ 40 (270)
Edge Bearing Strength⁷, ksi (MPa)	Fill	≥ 40 (270) ≥ 40 (270)
Flammability		Meets FAR 25.853 & 855 Appendix F Part I & III

Table shown reflects typical values and should not be used as design specifications.

¹Tensile Strength was tested and calculated per ASTM D638.
²Flexural Strength and Modulus were tested and calculated per ASTM D790.
³Water Absorption was tested and calculated per ASTM D570.
⁴Bond Strength was tested and calculated per ASTM D5868 using modified specimen preparation and test speed.
⁵Abrasion resistance was tested per ASTM D3389 with CS-10 Wheel, 500 grams of weight, and minor modifications to specimen preparation.
⁶Impact Strength was tested calculated per ASTM D5420 using a modified dart and specimen test frame.
⁷Edge Bearing Strength was calculated per ASTM D953 using a modified tension loading fixture.

Health Precautions

This product is safe to use and apply when recommended precautions are followed. Before using this product, read and understand the Safety Data Sheet (SDS), which provides information on health, physical and environmental hazards, handling precautions and first aid recommendations. For industrial use only. Keep away from children. Additional information can be found at: www.thegillcorp.com. For sales and ordering information call 1-626-443-6094.

Disclaimer

All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.

Gilliner® 1366B/1366E

Overview

Applications

Features

Availability

Construction

Specifications

Performance Properties, Typical

Health Precautions

Disclaimer

Join Our Team

Take your career to the next level and push the limits of possibility.

The Gill Corporation provides the products that solve your challenges.

Explore

Read

Collaborate

Resources

Connect