Gilliner ® 1366D is a high impact resistant and high wear resistant liner constructed from woven E-glass and S-glass cloth with nylon surface scrim and polyester resin system to optimize strength, weight, and cost. The combination of E- and S-glass reinforcement yields a higher strength-to-weight ratio as compared to E-glass only. This product also features a resin rich surface to prevent wear through over frame sections and attach points that are associated with repetitive bulk cargo loading.
貨艙的貨物襯裡，飛機的艙壁面板。
Designed for lower sidewalls where in-service conditions may result in wear through over frame sections, impact damage and/or fastener hole tear out at attach points. 1366D has been successfully used in Boeing 737 cargo bays.
| 表格形式 | 卷式 | |
|---|---|---|
| 厚度，英寸（毫米） | 0.045 (1.14) 0.060 (1.52) | 0.045 (1.14) – |
| 長度 | 典型 144 英寸（3,658 毫米） | 典型 150 英尺（45,720 毫米） |
| 寬度 | 典型 48 英寸（1,219 毫米） 最大 72 英寸（1,829 毫米） | 典型 48 英寸（1,219 毫米） 最大 60 英寸（1,524 毫米） |
| 顏色 | 自然的 | 自然的 |
樹脂： 聚酯纖維
加強： 編織E-和S-玻璃纖維布
表面： Nylon surface scrim
| TGC 部件號 | 1366D045 | 1366D060 | |
|---|---|---|---|
| 厚度，英寸（毫米） | 0.045 (1.14) | 0.060 (1.52) | |
| 重量，psf (kg/m2 ) | 0.42 (2.05) | 0.61 (2.98) | |
| 抗拉強度1, 西 (兆帕) | 經 | 77 (531) | 87 (600) |
| 充滿 | 72 (496) | ||
| 抗磨性2 , g/1000 次循環 | 0.02 | 0.06 | |
| 衝擊強度3 , 英尺-磅 (牛米) | 32 (43) | 41 (56) | |
| 邊緣承載強度4, 西 (兆帕) | 經 | 47 (324) | 56 (386) |
| 充滿 | 44 (303) | 46 (317) | |
| 抗彎強度5, 西 (兆帕) | 經 | 35 (241) | |
| 充滿 | |||
| 彎曲正切模量5, 微星 (GPa) | 經 | 2.5 (17) | 2.5 (17) |
| 充滿 | 2.9 (20) | ||
| 易燃 | 符合 FAR 25.853 和 855 附錄 F 第 I 和 III 部分 | ||
所示表格反映了典型值，不應用作設計規範。
1拉伸強度根據 ASTM D638 進行測試和計算。
2耐磨性是根據 ASTM D3389 使用 CS-10 輪、500 克重量和對樣品製備進行微小修改進行測試的。
3衝擊強度是根據 ASTM D5420 使用改進的落鏢和試樣測試框架測試計算得出的。
4邊緣承載強度是根據 ASTM D953 使用改進的張力加載夾具計算的。
5彎曲強度和模量根據 ASTM D790 進行測試和計算。
當遵循推薦的預防措施時，本產品可以安全使用和應用。使用本產品前，請閱讀並理解 安全數據表 (SDS)，其中提供有關健康、身體和環境危害、處理預防措施和急救建議的信息。僅供工業使用。遠離兒童。可以在以下位置找到更多信息： www.thegillcorp.com.如需銷售和訂購信息，請致電 1-626-443-6094。
All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.
