PAA-CORE® 5056 aluminum honeycomb is the industry’s highest performing core material. Phosphoric acid anodized and coated with a proprietary primer, it outperforms all other core materials.
Decades of operational experience have shown that bond durability between core and face sheets is critical to long part life, and for this, PAA-CORE® has no equal. Independent analysis confirms the environmental performance durability of PAA-CORE®, assuring a lower total life cost than with other core materials. PAA-CORE® also has unsurpassed corrosion resistance, experiencing only minimal weight loss after 31 days in an acidified salt spray chamber, which simulates the harshest environmental conditions. PAA-CORE® retained virtually all of its physical properties during this test.
More importantly, PAA-CORE® outperforms non-metallic core materials. With significantly higher strength-to-weight ratios and hot/wet strength, it offers designers higher performance with lower weight. In addition, it saves money, since PAA-CORE® costs less than non-metallic cores. There is simply no equivalent to PAA-CORE®.
| 標準 | 最大限度 | 寬容 | ||||
|---|---|---|---|---|---|---|
| 英寸 | 毫米 | 英寸 | 毫米 | 英寸 | 毫米 | |
| 絲帶（大） | 48 | 1219 | 100 | 2540 | +2.0 / -0.0 | +50.8 / -0.0 |
| 橫向 (W) | 96 | 2438 | 144 | 3658 | +4.0 / -0.0 | +101.6 / -0.0 |
| 厚度 (T) | 35 | 889 | ||||
| 高達 4 英寸（102 毫米）T | ±0.005 | ±0.127 | ||||
| 超過 4 英寸（102 毫米）T | ±0.062 | ±1.575 | ||||
| 密度 | 見機械特性表 | ±10% | ||||
| 像元大小 | 見機械特性表 | ±10% | ||||
基質： 5056鋁
塗層： PAA底漆
When ordering, please specify PAA-CORE® 5056 using the following format:
Example: PAA – 5056 – 3.1 – 3/16 – N – E, where
| 產品 | 合金 | 密度 | 像元大小 | 穿孔或非穿孔 | 擴展或未擴展 |
|---|---|---|---|---|---|
| PAA | 5056 | 3.1 | 3/16 | A片 | E或U |
| Mechanical Characteristics (Typical Values – US units) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 穩定壓縮 力量 | 壓碎 力量 | 剪切 力量 | 剪切 模數 |
||||||
| 磅/英尺3 – inches – inches | 壓力 | 壓力 | 壓力 | ksi | |||||
| 大號 | W | 大號 | W | ||||||
| 75° F | 350° F | 75° F | 75° F | 350° F | 75° F | 350° F | 75° F | ||
| 3.1 – 1/8 – .0007 | 355 | 230 | 180 | 255 | 170 | 160 | 110 | 32 | 16 |
| 4.5 – 1/8 – .0010 | 700 | 480 | 320 | 450 | 274 | 260 | 180 | 51 | 25 |
| 6.1 – 1/8 – .0015 | 1210 | 780 | 550 | 700 | 425 | 410 | 245 | 77 | 37 |
| 8.1 – 1/8 – .0020 | 1920 | 1350 | 850 | 960 | 590 | 575 | 340 | 112 | 50 |
| 10.0 – 1/8 – .0025 | 2200 | 1625 | 1200 | 1190 | 830 | 675 | 455 | 140 | 60 |
| 12.0 – 1/8 – .0030 | 3250 | 1950 | 1550 | 1725* | 1430* | 1025* | 465* | 160 | 75 |
| 2.6 – 5/32 – .0007 | 270 | 160 | 130 | 205 | 130 | 120 | 90 | 24 | 12 |
| 3.8 – 5/32 – .0010 | 510 | 350 | 230 | 340 | 230 | 200 | 175 | 41 | 20 |
| 5.3 – 5/32 – .0015 | 875 | 625 | 435 | 560 | 370 | 335 | 230 | 64 | 31 |
| 6.9 – 5/32 – .0020 | 1350 | 1040 | 660 | 775 | 525 | 440 | 300 | 91 | 42 |
| 2.0 – 3/16 – .0007 | 205 | 115 | 80 | 145 | 100 | 87 | 70 | 17 | 9 |
| 3.1 – 3/16 – .0010 | 420 | 230 | 180 | 270 | 170 | 155 | 110 | 32 | 16 |
| 4.4 – 3/16 – .0015 | 675 | 475 | 310 | 435 | 260 | 250 | 170 | 50 | 24 |
| 5.7 – 3/16 – .0020 | 1010 | 730 | 480 | 570 | 410 | 335 | 225 | 70 | 34 |
| 6.9 – 3/16 – .0025 | 1250 | 1025 | 660 | 765 | 525 | 450 | 300 | 91 | 42 |
| 1.6 – 1/4 – .0007 | 115 | 80 | 60 | 92 | 70 | 62 | 40 | 13 | 6 |
| 2.3 – 1/4 – .0010 | 270 | 150 | 120 | 185 | 110 | 105 | 75 | 21 | 11 |
| 3.4 – 1/4 – .0015 | 490 | 300 | 190 | 300 | 190 | 180 | 125 | 35 | 18 |
| 4.3 – 1/4 – .0020 | 630 | 460 | 300 | 410 | 255 | 235 | 160 | 48 | 24 |
| 5.2 – 1/4 – .0025 | 830 | 625 | 380 | 500 | 360 | 310 | 195 | 62 | 30 |
| 6.0 – 1/4 – .0030 | 1000 | 775 | 525 | 640 | 415 | 375 | 240 | 75 | 36 |
| 7.9 – 1/4 – .0040 | 1580 | 1300 | 820 | 900 | 565 | 540 | 330 | 108 | 49 |
| 2.3 – 3/8 – .0015 | 230 | 150 | 120 | 175 | 110 | 100 | 75 | 21 | 11 |
| 3.0 – 3/8 – .0020 | 350 | 220 | 160 | 250 | 165 | 150 | 100 | 30 | 15 |
| 3.7 – 3/8 – .0025 | 450 | 325 | 220 | 325 | 225 | 190 | 130 | 40 | 20 |
| 4.2 – 3/8 – .0030 | 550 | 410 | 290 | 395 | 260 | 225 | 155 | 47 | 23 |
| 5.4 – 3/8 – .0040 | 850 | 650 | 450 | 565 | 390 | 325 | 200 | 66 | 32 |
有關最小值，請參閱 AMS-C-7438。 *梁剪切
| Mechanical Characteristics (Typical Values – SI/metric units) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 穩定壓縮 力量 | 壓碎 力量 | 剪切 力量 | 剪切 模數 |
||||||
| 磅/英尺3 – inches – inches | 兆帕 | 兆帕 | 兆帕 | 兆帕 | |||||
| 大號 | W | 大號 | W | ||||||
| 23° C | 177° C | 23° C | 23° C | 177° C | 23° C | 177° C | 23° C | ||
| 3.1 – 1/8 – .0007 | 2.45 | 1.59 | 1.24 | 1.76 | 1.17 | 1.10 | 0.76 | 221 | 110 |
| 4.5 – 1/8 – .0010 | 4.83 | 3.31 | 2.21 | 3.10 | 1.89 | 1.79 | 1.24 | 352 | 172 |
| 6.1 – 1/8 – .0015 | 8.34 | 5.38 | 3.79 | 4.83 | 2.93 | 2.83 | 1.69 | 531 | 255 |
| 8.1 – 1/8 – .0020 | 13.24 | 9.31 | 5.86 | 6.62 | 4.07 | 3.96 | 2.34 | 772 | 345 |
| 10.0 – 1/8 – .0025 | 15.17 | 11.20 | 8.27 | 8.20 | 5.72 | 4.65 | 3.14 | 965 | 414 |
| 12.0 – 1/8 – .0030 | 22.41 | 13.44 | 10.69 | 11.89* | 9.86* | 7.07* | 3.21* | 1103 | 517 |
| 2.6 – 5/32 – .0007 | 1.86 | 1.10 | 0.90 | 1.41 | 0.90 | 0.83 | 0.62 | 165 | 83 |
| 3.8 – 5/32 – .0010 | 3.52 | 2.41 | 1.59 | 2.34 | 1.59 | 1.38 | 1.21 | 283 | 138 |
| 5.3 – 5/32 – .0015 | 6.03 | 4.31 | 3.00 | 3.86 | 2.55 | 2.31 | 1.59 | 441 | 214 |
| 6.9 – 5/32 – .0020 | 9.31 | 7.17 | 4.55 | 5.34 | 3.62 | 3.03 | 2.07 | 627 | 290 |
| 2.0 – 3/16 – .0007 | 1.41 | 0.79 | 0.55 | 1.00 | 0.69 | 0.60 | 0.48 | 117 | 62 |
| 3.1 – 3/16 – .0010 | 2.90 | 1.59 | 1.24 | 1.86 | 1.17 | 1.07 | 0.76 | 221 | 110 |
| 4.4 – 3/16 – .0015 | 4.65 | 3.28 | 2.14 | 3.00 | 1.79 | 1.72 | 1.17 | 345 | 165 |
| 5.7 – 3/16 – .0020 | 6.96 | 5.03 | 3.31 | 3.93 | 2.83 | 2.31 | 1.55 | 483 | 234 |
| 6.9 – 3/16 – .0025 | 8.62 | 7.07 | 4.55 | 5.27 | 3.62 | 3.10 | 2.07 | 627 | 290 |
| 1.6 – 1/4 – .0007 | 0.79 | 0.55 | 0.41 | 0.63 | 0.48 | 0.43 | 0.28 | 90 | 41 |
| 2.3 – 1/4 – .0010 | 1.86 | 1.03 | 0.83 | 1.28 | 0.76 | 0.72 | 0.52 | 145 | 76 |
| 3.4 – 1/4 – .0015 | 3.38 | 2.07 | 1.31 | 2.07 | 1.31 | 1.24 | 0.86 | 241 | 124 |
| 4.3 – 1/4 – .0020 | 4.34 | 3.17 | 2.07 | 2.83 | 1.76 | 1.62 | 1.10 | 331 | 165 |
| 5.2 – 1/4 – .0025 | 5.72 | 4.31 | 2.62 | 3.45 | 2.48 | 2.14 | 1.34 | 427 | 207 |
| 6.0 – 1/4 – .0030 | 6.89 | 5.34 | 3.62 | 4.41 | 2.86 | 2.59 | 1.65 | 517 | 248 |
| 7.9 – 1/4 – .0040 | 10.89 | 8.96 | 5.65 | 6.21 | 3.90 | 3.72 | 2.28 | 745 | 338 |
| 2.3 – 3/8 – .0015 | 1.59 | 1.03 | 0.83 | 1.21 | 0.76 | 0.69 | 0.52 | 145 | 76 |
| 3.0 – 3/8 – .0020 | 2.41 | 1.52 | 1.10 | 1.72 | 1.14 | 1.03 | 0.69 | 207 | 103 |
| 3.7 – 3/8 – .0025 | 3.10 | 2.24 | 1.52 | 2.24 | 1.55 | 1.31 | 0.90 | 276 | 138 |
| 4.2 – 3/8 – .0030 | 3.79 | 2.83 | 2.00 | 2.72 | 1.79 | 1.55 | 1.07 | 324 | 159 |
| 5.4 – 3/8 – .0040 | 5.86 | 4.48 | 3.10 | 3.90 | 2.69 | 2.24 | 1.38 | 455 | 221 |
有關最小值，請參閱 AMS-C-7438。 *梁剪切
當遵循推薦的預防措施時，本產品可以安全使用和應用。使用本產品前，請閱讀並理解 安全數據表 (SDS)，其中提供有關健康、身體和環境危害、處理預防措施和急救建議的信息。僅供工業使用。遠離兒童。可以在以下位置找到更多信息： www.thegillcorp.com.如需銷售和訂購信息，請致電 1-626-443-6094。
All recommendations, statements, values and technical data herein are based on tests The Gill Corporation believes to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. Users shall rely on their own information and tests to determine suitability of the product for the intended use and assume all risks and liability resulting from their use of the product. The Gill Corporation’s sole responsibility shall be to replace that portion of the product that proves to be defective. The Gill Corporation will not be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements not contained in a written agreement signed by an officer of The Gill Corporation shall not be binding upon The Gill Corporation. Alcopan™, Alphex®, CGH® Dura-Core®, Gillfab®, Gillfloor®, Gilliner®, Gillite®, Gillfists®, GillVANA®, Higrid®, Hushgrid®, PAA-Core®, Plygrid®, Shapegrid®, Strikegrid®, Trussgrid® are registered trademarks of The Gill Corporation.
